Advanced Melt Flow System. The 6MPCA is the most advanced digital model offered within the Ray-Ran range of melt flow index testers. The operating. Find the most up-to-date version of ASTM D at Engineering ASTM D(). Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications. standard by ASTM.
|Published (Last):||17 May 2011|
|PDF File Size:||7.97 Mb|
|ePub File Size:||12.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
This means that the? Next Checking to see if you are a returning visitor…. When charging wstm complete, pack down the PVC with the phenolic-coated charging tool by repeated thrusts.
Thus, implications with respect to PVC molecular structural changes can be detected and predicted. Link to Active This link will always route to the current Active version of the standard. If the difference between the two specimens is greater than 0. If charging time is greater than 1 min, clean out the instrument and repeat the procedure. These changes are due to three types of measured instability in polymers:.
For PVC, N varies from 0. As a asgm, each specimen should be about 20 to 30 mm long. The sensitivity of this test method makes it useful for correlating with processing conditions and as an aid in predicting changes in processing. This average value is axtm PVC? Thus, this test is able to detect and follow profound changes which occur during extrusion, injection molding, milling, or mixing.
Report as percent PVC instability. Users of this test method should apply the principles outlined in Practice E to generate data speci?
ASTM D3364 Flow Rates for Poly Vinyl Chloride
This weight is effective for all semirigid PVC and even some nonrigid compounds. Your comments are invited either for asstm of this standard or for additional standards and should be addressed to ASTM International Headquarters. Subscribe to Instron News! The dimensions of the regular die are shown in Fig.
The instrument is now ready for the next test. Make the cut quickly and neatly for best precision. This standard is subject ast, revision at any time by the responsible technical committee and must be reviewed every? The following explanations of r and R WaveMatrix 2 for Dynamic Testing. Originally published as D — This test method is used for quality-control tests on PVC compounds that have a wide range of melt viscosities.
The quantity of material introduced into the barrel is 2.
Glossary of Materials Testing Terms. This test is able to detect and follow profound changes, which occur during extrusion, injection molding, milling, or mixing, that are due to three types of measured instability in polymers, including Thermal instability due to temperature effect, Shear instability due to breaking of polymer bonds, and Rheological instability due to non-uniform distributions of widely different viscosity or molecular weight elements.
Under these conditions, average the values after discarding the? Note 1—There is no known ISO equivalent to this standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM D3364 – 99(2011)
Since Q is the volumetric? In addition to the properties mentioned in Test Method Dthis technique is sensitive to plasticizer content, polymer molecular weight, polymer stability both thermally and rheologicallyshear instability, and general composition.
Push out any molten PVC in the ori? Asm previous edition D — Software for Series Systems.
ASTMD Standard Test Method for Poly(Vinyl ride) with Molecular Structural Implications_百度文库
If instability still occurs, particularly at high? This statement further de? Most regulators designed for Test Method D cannot control better than The cause of this unstable condition should be studied and understood. Email addresses must contain the symbol. However, as a one-point measure of flow relative to shear rate, its one drawback is that the same PVC melt flow values can be obtained for materials having different processibility; the chance of this happening is minimized, however, if the compounds are similar in composition.
A clean sharp cut is desirable so that succeeding portions will extrude straight, not curled. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Dry off the cooled die with a cloth and inspect to see that the ori?