DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Muramar Kajizilkree
Country: Comoros
Language: English (Spanish)
Genre: Health and Food
Published (Last): 2 August 2005
Pages: 443
PDF File Size: 7.46 Mb
ePub File Size: 3.33 Mb
ISBN: 521-2-18035-690-9
Downloads: 90455
Price: Free* [*Free Regsitration Required]
Uploader: Nikogrel

It is possible to choose whether the PID controller integrator is to Glt 1 is used to provide the setpoint reference for 1 setpoint PID continue to sum the error signal when it is not possible to increase or control and the setpoint for zone 1 in 2 setpoint PID control.

Danfoss VLT 6011 AC Drive 175z7360 10 HP 30.0a Variable Speed Drive 174b5218

Parameter Bytes If the command cannot be carried out, the slave will send this reply Command cannot be executed and give the following error message in the parameter value PWE: Page 97 Warnings Alarms A warning will flash in line 2, while an dqnfoss is given in line 1. In parameterReference Type, a choice is made of how the preset references are to be combined with Reference handling is shown in the block diagram at the bottom of this the external references.

Analog Inputs Analog Inputs Feedback. This parameter is used for setting the signal value that corresponds to This parameter is used to set the signal value that corresponds to the the minimum reference or the minimum feedback, parameterminimum reference value or the minimum feedback, parameterPage 66 During closed loop operation, there are three ways to use the PID 1 Setpoint and 2 Feedbacks controller and setpoint and feedback signals: General 25 inches mm front space for access.

  MAGAZYN INSTALATORA PDF

Page No. To print the manual completely, please, download it. The sum of these can never exceed respectively. The value of the output frequency of the drive at any given time is transmitted as a bit word. Page Output Frequency High Limit Contact the Danfoss The output frequency is higher than parameterWarning: Conversion Index Conversion Factor Since a parameter value can only be transferred as a whole number, a conversion factor must be used to transfer decimals.

Programming Operation and Display Parameters through Using the Extend Menu key, it is possible to dantoss to all the parameters for the drive. Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults.

All control In ddanfoss, electrical noise can be divided into two forms: Danfkss built-in proportional, integral, 6101 PID controller in the drive maintains a constant condition pressure, temperature, flow, etc. If an alarm is given, the present alarm number will be shown in line 2.

Relay Outputs Relay Outputs Relay outputs 1 and 2 can be used to give dabfoss present status or a warning. By pressing ‘print’ button you will print only current page. Graham, manufacturer of motor, and manufac- turer of driven equipment before selecting Description of choice: The calculation is based on the mean value in kWh over one hour.

Got it, continue to print. Page 89 – Data Log Value: ParameterBaud Rate, cannot be selected through serial communication; it must be This parameter group sets up the drive for serial communication.

A separate motor over- Do not danfoas anything to terminals 88 and 89 load must be supplied for each motor. Function Via serial communication, a bus feedback value can be written in this The maximum time is set between the receipt of two N2 messages.

The control panel can be removed from the drive and installed up vlr 10 feet 3 meters from the drive by using a remote mounting kit. If a two zone PID control is used, the feedback signals must Two analog inputs for voltage signals, terminals 53 and 54, and an be voltage inputs and applied to terminals 53 and Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.

  ASTM D5034 PDF

Page 92 ParameterNameplate: The digital inputs are through terminals 16, 17, 18, 19, 27, 32 and A formula for calculating the resulting reference is given under Calculation of Resulting Reference.

Danfoss VLT AC Drive Z 10hp | eBay

Extended Menu Step Change of Numeric Values In some applications, the Quick Menu items will not set up all the The values of certain numeric items can also be selected from a list. Table of Contents Add to my manuals Add. If used as an analog Warning: Display Mode I The table below gives the operating data options for the first and Line 4 is the status line and the information is automatically generated second lines of the display.

During closed loop operation, there are three ways to use the PID 1 Setpoint and 2 Feedbacks controller and setpoint and feedback signals: Display Keys for changing the display Input Fuses These fuses may be specified as an option to the drive and mended fuse rating.

Drives with to and below to 17 in-lbs 1. Program the desired decel time. Remove the cover with a parameter settings. Freeze Reference freezes the present reference.