DataSheet: PDF icon HT12E is an encoder integrated circuit of series of encoders. They are paired with series of decoders for use in. Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and HT12F is used to decode 12 bits of address information.. 盛群半導體為國內. HT12D. 8. 4. L. Ö. RC oscillator DIN active ²Hi² 18 DIP/20 SOP .. The recommended oscillator frequency is fOSCD (decoder) @ 50 fOSCE (HT12E encoder). @ The information appearing in this Data Sheet is believed to be.

Author: Dujinn Malajind
Country: India
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 January 2014
Pages: 200
PDF File Size: 17.95 Mb
ePub File Size: 11.91 Mb
ISBN: 617-2-23770-943-6
Downloads: 25191
Price: Free* [*Free Regsitration Required]
Uploader: Telrajas

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. This pin has to be connected to Ground 0V to enable the Transmission.

Interface SD Card with Arduino.

Thus this helps in setting up oscillations in the IC. Basically found in applications of remote control systems. Gone are the days when we used to use wires to connect two devices to datasheeet a communication path. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

TB Stepper Motor Driver 4.

The IC has a built in oscillator. This site uses cookies. You can know to set up the HT12D after this from here. At low signal data is transferred via antenna and received by Receiver IC which xatasheet decodes it to original parallel data.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

Choosing Battery for Robots. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. Skip to main content.


HT12E Encoder IC

They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. Thanks a lot for helping us to maintain competitive prices.

The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product.

We dztasheet set the bits in same pattern on Encoder and Decoder IC to pair them. If you want security you can connect any of the 8 pins to 5V to make it high. In this image I have made all four data anc as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. They are paired with 2 12 series of decoders for use in hh12e control system applications.

This is an CMOS logic integrated circuit encoder. TL — Programmable Reference Voltage. HT12E has a transmission nad pin which is active low. SPI Module of Arduino. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. The primary function of HT12E is to encode a bit and send daatsheet out through the output pin.


The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data. They can also be connected to switches to manually send and receive data.

Return and Refund Policy. The IC is has a wide range of operating voltage from 2.

I am now going to tell you about to control a certain robot wirelessly rather than using wires. These pins are generally shorted datasjeet a resistor.

HT12E is an encoder integrated circuit of 2 12 series of encoders. This oscillator can be used by connecting these two pins through a 1M Resistor. This cycle is repeated as long as TE is kept low. Whenever an active low signal is applied at its TE pin then only the parallel data gets transferred serially at the output, otherwise the IC is in high impedance state.

Arduino based GPS receiver. Submitted by admin on 30 October This high-density System-in-Package SiP integrates controller, power switches, and datasueet components. This pin outputs the parallel data serially. Used for interfacing RF circuits generally MegaHz.

HT12E begins a 4-word transmission datasjeet upon receipt of a transmission enable. Full Name Email Address.